Войти
/
регистр
Language
English
Deutsch
Française
Español
Português
Italia
Русский
日本語
한국어
简体中文
繁體中文
Пожалуйста, введите полный или частичный номер детали производителя с минимум 3 буквами или цифрами
Запросить цену
0
Главная
Товары
Производители
Горячие продукты
открытие
Новости
Блоги
Вопросы и ответы
обслуживание
Контроль качества
информация о доставке
Платежная информация
Вопросы и ответы
Политика возврата
Наша компания
Главная
> Вопросы и ответы
все категории
Рекомендую
Technology
MCU
Hardware design
EDA & PCB design
Applications
Development board
Original factory
Embedded
DIY maker
DSP technology
FPGA/CPLD
College area
Linux system
MCU application
STM32
MCS 51
MSP430 MCU
AVR MCU
PIC MCU
Circuit design
Power technology
Electronic Component
RF / ICT
Sensing control
EMC/EMI
PCB Technology / Design / Customization
Proteus simulation
Labview simulation
EDA circuit tool
Consumer Electronics
Auto electronics
Industrial Electronics
Other applications
Medical electronics
LED application
Raspberry Pi
Arduino
Bananapi
NanoPi
MicroPython
Seeed
Intel Development board
Linkit Smart 7688
Galileo/Edison
Freescale FRDM
Rayeager PX2
Waveshare
IntoRobot
Beaglebone Black
Firefly open source hardware
ZLG
Orange Pi
DFRobot
WRTnode
TigerBoard
Maxim technology
NXP technology
ON technology
WIZnet network technology
TI technology
ADI technology
Other original technology
Rohm technology
Cypress technology
EPSON technology
Rochester
TOSHIBA technology
LITEON technology
Micron technology
Preferred materials
Вопросы
Рекомендую
Самый последний
0
Ответить
How to determine the driving capability of the signal?
Single-ended signal drive
March 23, 2021
by Miles
2386
0
Ответить
Is this power circuit charging or discharging?
Discharge
March 23, 2021
by Jared
2436
0
Ответить
When the STM32F030C8 external io port interrupt level is kept at 1.2V, the interrupt is always triggered and cannot come out.
STM32
March 17, 2021
by Matthew
2398
0
Ответить
Damaged half-bridge drive circuit components.
Brushless Motor
March 17, 2021
by Daniel
2379
0
Ответить
What caused the burning of the TVS at the power input terminal?
TVS
March 17, 2021
by Jacob
2403
0
Ответить
How to control the power supply of two power supplies.
control
March 15, 2021
by Aurelius
2486
0
Ответить
What is the function of the diode between these two operational amplifiers?
diode
March 15, 2021
by Nena
2246
0
Ответить
What is the difference between high-end detection and low-end detection when detecting current?
Current
March 15, 2021
by Hardy
2461
0
Ответить
Measurement of the inductance of the LLC resonant circuit.
LLC
March 11, 2021
by Angel
2056
0
Ответить
When do I use voltage regulators and voltage dividers?
Interrupt
March 11, 2021
by Jessica
2055
0
Ответить
Why does the amplifier become a hysteresis comparator after adding positive feedback?
Amplifier
March 11, 2021
by Zachary
1539
0
Ответить
What is the function of the voltage regulator in the button circuit?
Zener tube
March 5, 2021
by Ernest
2006
0
Ответить
51 single-chip production running water lamp does not light up.
51 single chip microcomputer
March 5, 2021
by Lina
2137
0
Ответить
The voltage divider circuit MOS tube is easy to be damaged. What is the problem with the design?
MOS tube
March 5, 2021
by Laurel
2201
0
Ответить
The op amp is used as a constant current source to drive the stepper motor to generate oscillations. How to modify the circuit diagram?
oscillation
March 5, 2021
by Reggie
1956
0
Ответить
Can I use labview to generate an arc when I know the starting point? At the same time, the arc of this arc can be changed?
labview
March 5, 2021
by Deja
2108
0
Ответить
Can BQ24610 use DC as input?
DC-DC
March 4, 2021
by Talon
1999
0
Ответить
Do I have to use optocouplers to connect AD421 and MCU?
AD421
March 2, 2021
by Marquez
2113
0
Ответить
What is the specific principle of adding two resistors and two transistors to the resistor step-down circuit in the figure?
Buck
March 2, 2021
by Faris
2087
0
Ответить
I want to ask why LM393 can't output low level?
LM393
March 2, 2021
by Jacobi
1549
Задать вопрос
Горячие вопросы и ответы
How to determine the driving capability of the signal?
[подробности]
Is this power circuit charging or discharging?
[подробности]
When the STM32F030C8 external io port interrupt level is kept at 1.2V, the interrupt is always triggered and cannot come out.
[подробности]
Damaged half-bridge drive circuit components.
[подробности]
What caused the burning of the TVS at the power input terminal?
[подробности]
How to control the power supply of two power supplies.
[подробности]
What is the function of the diode between these two operational amplifiers?
[подробности]
What is the difference between high-end detection and low-end detection when detecting current?
[подробности]
Горячие продукты
Выберите ваше местоположение